Precision PCB Fabrication, PCB Assembly, Components sourcing,  No MOQ...
You are here: Home » About Us » PCB Blogs » Knowledge » Four features to consider in PCB layout

Four features to consider in PCB layout

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
sharethis sharing button

Over the years there's been a movement towards designing smaller and faster electronics but smaller and faster can also mean more difficult to fabricate resulting in higher costs. While some may put more emphasis on performance related attributes others may be more flexible with their designs and be more concerned with keeping costs down. Understanding design guidelines will help ensure that your design is efficient; the right mix of performance and cost for your specific requirements. Following design rules will save you time and money, making your printed circuit board project success.

Holes

When you are creating your design you should only be concerned with the finished hole size. You do not need to specify the exact drill size that needs to be used. A good PCB fabricator will make the required adjustments to the drill size in order to get as close as possible to the desired finished hole size. The exception would be a hole that does not require plating and in those cases the fabricator would use the drill size specified by the designer.

One important consideration are the holes on the board; primarily the hole size and how the holes will be connected to traces in the design. The ability to drill smaller holes has increased greatly in the last decade. Today, it is standard to be able to have a finished hole size of 0.010″ but of course, if you can use 0.015″ or 0.020″ the process and quality will be much easier to maintain.

In order for that hole to make a connection from a copper trace on top of the board to a copper trace on bottom of the board, that hole must be plated with copper. The more copper that is plated, the smaller the hole will become. Typical plating in a hole uses approximately 1 oz of copper or around 0.0014″ thick. This will ensure a solid electrical connection from the copper pad on top of the hole to the copper pad on the bottom of the hole.

It's also important to consider the difference in the size of the hole that is drilled into a board versus the finished hole size after copper plating. For example, a 0.010" finished hole size may be drilled with a 0.012" drill bit.

通孔-2

Line width and space

One of the other primary areas for consideration is the size and spacing of copper features; often referred to as the trace and space on the board. The copper trace is the line that connects components to other components or to vias (holes plated with copper). It essentially acts as the wire in your connections. A trace with a larger width is easier to manufacture and a trace with a smaller width is more difficult to manufacture. 0.005" is a good minimum trace width but 0.007" or 0.008" would help ensure that the manufacturing process produces a high quality board. While a trace width smaller than 0.005" is possible the extra care, processes and restrictions required can result in higher costs.

The same is true of spacing. A minimum of 0.005” of space between copper traces, or between copper traces and other features like holes and ground planes, will allow for efficient manufacturing. Spacing greater than 0.005” will help prevent instances of copper features "shorting out".

Copper to edge Space

Another key rule is related to the spacing from copper to the edge of the board. Ideally any copper used in your design should be no closer than 0.010" to the edge of the board. Any closer than 0.010" will increase the risk of copper being exposed after the board has been routed.

Pads

Related to the finished hole size another important consideration is the pad size for the hole. The pad can be defined as the copper that surrounds the hole at the top or bottom of the board. The purpose of the pad is to ensure that the copper plated in the hole makes a solid connection to the traces that connected to the pad. Ideally the pad size should be at least 0.015″ larger than the hole size. For instance if you have a finished hole size of 0.010″ then the final size of the pad for that hole would be 0.025″.

Table of Content list
Sign up for our newsletter

PCB Fab

PCB Assembly

Capabilities

CONTACT US
General Inquiry
Email: sales@syspcb.com
Phone: +86-0769-82201689
Fax: +86-0769-87799518

Tech Support
Email: tech@syspcb.com
Phone: +86-0769-82201689
SOCIAL NETWORKS
Copyright © 2024 SYS Technology Co., Ltd. All Rights Reserved.|Privacy policy|sitemap
We use cookies to enable all functionalities for best performance during your visit and to improve our services by giving us some insight into how the website is being used. Continued use of our website without having changed your browser settings confirms your acceptance of these cookies. For details please see our privacy policy.
×