Technical
How to Judge the Acceptance of PCB Quality
Which Color Circuit Board Sells the Most Expensive
Method to Solve the Noise Interference of Power Supply on High-frequency PCB Board
Disassembly Skills of Chip Components on PCB
What Factors Should Be Considered in the Selection of High-frequency PCB CCL
How to Place Special Components during PCB Layout
What Are the Functions of Capacitors in Circuits?
Testing Techniques for Common Electronics Components
What to do if There is a Short Circuit on the PCB
Desoldering Principles and knowhow during PCBA Processing
Black Oxidation of the Inner Layer of the Multilayer PCB
How to Ensure the High-performance Design of PCB
What Is the Printing Process of SMT Solder Paste?
PCB without fiducial mark, Is There Any Way to do SMT for It
What Are the Benefits of Reserving Break-up Tab for PCB Production
How Does SMT Affect PCB Production Time and Speed It Up
Classification of PCBs from three aspects
Common Problems and Solutions for Dry Film pasting during PCB Manufacturing process
Several Elements to Inspect after PCB Design
What is a halogen-free circuit board?
What Do Capacitive Coupling and Decoupling Mean?
What Are the Differences Between PCB Paste Mask and Solder Mask?
How PCBA Is Packaged and Shipped
How long can PCBA finished products be stored?
What Are the Differences and Relations Between PCB, PCBA, and SMT?
PCB Baking Specifications
PCB "Solder Mask Tenting" and "Solder Mask Opening"
Five reasons for PCB deformation and six solutions
Importance of first article inspection of PCBA board
Temperature zone standard for SMT reflow soldering
Small and medium volume PCB manufacturers in China
The main reason for PCBA cleaning
For power filter, the more capacitors, the better?
What does PCBA programming mean?
Content of PCB incoming testing
What conditions must be met for PCB circuit board soldering?
What is Blind via and Buried via
PCBA Manufacturers Temperature and Humidity Sensitive Components Management
Why choose Shenzhen SMT processing factory?
How long does it take to calculate the quotation for PCBA manufacturing?
Introduction of PCB design clearance requirements
Explanation of BOM, DIP, SMT, SMD
Introduction of the process of PCBA prototype
How to prevent pseudo soldering or cold soldering defects in PCBA manufacturing?
Factors that affect the Price of FPCB
What information is required for SMT processing at PCBA factory?
Skills of using 0ohm resistor in PCB design
How to select a PCBA manufacturer
SMT processing solder joint quality inspection
Characteristics difference between immersion gold PCB and gold plating PCB
Common malfunctions of Circuit Board Caused by Moisture
A Few Rules about PCB Panelization
Compare of multi-layer PCB with single/double layer PCB
Why do we need to introduce so many subdivided GND
Difference between immersion gold boards and gold plating boards
Aluminum PCB structure
Classification of different GND in circuit
Why PCB baking is necessary during manufacturing process
The handle and precautions of OSP board in SMT process
How to choose capacitors for filter decoupling
How to choose filter capacitor for switching power supply
5 database need for SMT process
Function of three-terminal capacitor
Introduction of PCB OSP surface treatment
Method of inspecting the quality of SMT by step
How to find the short point between VCC and GND
Difference between 850nm and 940nm infrared LED
Component layout of PCB SMT DFM
Pad shape influence on the strength and reliability of the soldering joints
The difference between high temperature solder paste and low temperature solder paste
Introduction to manual welding processing
Manual visual inspection in PCBA processing
Characteristics of the conformal coating process
Difference between hardware engineers and software engineers
PCBA processing operation rules
China PCB upstream materials has continued to soar
Difference between serial buses and parallel buses
The key points of quality control in PCBA processing
Common causes of solder beading during SMT process
Analysis of the advantages and disadvantages of HASL PCB surface
Requirements for layout of components during SMT assembly
Selection of electronic components and CCL for PCBA
Performance and appearance quality inspection of components.
Quality and Reliability of SMT Chip Processing and Production
Coupling and decoupling function of capacitor
Two methods to connect digital ground and analog ground
Common sense in SMT process

Importance of first article inspection of PCBA board

Many electronics companies do not care about the first article inspection of PCBA board when they cooperate with PCBA manufacturers. This doesn’t means that they do not know the step, but that they do not care about the importance of this step, nor do they think it plays an important role. In this regard, the first article inspection of the PCBA board is very important! Be sure to pay attention to the first article inspection of the PCBA board. Today China PCB assembler SYS Technology will tell you why the first article inspection is so important!

What is the first article inspection of PCBA board?

PCBA first article inspection


The first article inspection of PCBA board is to inspect the first batch or several batches of products after each shift or production line is put into production. Because it is a specific sample collected before mass production, so it is also called the first article inspection.

The quantity of the first article inspection varies according to the requirements of the enterprise or customer, but generally speaking, the first article inspection requires inspecting the products, and then the products can be put into mass production after inspected products being qualified. This is the link that conventional PCBA manufacturers will follow, and its purpose is self-evident.

What are the benefits of PCBA board first article inspection? Where is the importance?

In order to prevent the occurrence of poor quality, repair or scrapping of large quantities of products during the production process, PCBA manufacturers will conduct the first article inspection in advance. Its benefits are reflected in three aspects:

1. Avoid wasting resources

Because the first article inspection of PCBA board avoids the inferior quality, repair and scrapping of a large number of products, it can make better use of resources without wasting a lot of resources. This is a kind of cost control for enterprises, which can reduce the cost investment of PCBA manufacturers and electronic enterprises.

2. Quality Control

The first article inspection of PCBA board is an effective means to control the production process in advance. It can control product quality, help companies better determine the production quality of this batch of products, and improve their economic benefits.

3. Improve corporate reputation

No matter how good the quality is, if there is a lot of waste in the production process and the success rate is low. Such PCBA manufacturers are not what electronics companies want. Therefore, in order to improve their image and reputation, PCBA manufacturers will control product quality, success rate, pass rate and quality rate. When these data exceed the standard, they will have a good reputation among the peers and attract more customers to cooperate.

In addition, the importance of the first article inspection of the PCBA board is also reflected in the cost. While saving costs, it can also improve production efficiency and reduce enterprise cost and investment. Both PCBA manufacturers and electronic companies will get more profits. And if companies want to attract customers through cost down, they don’t have to worry about losing money.

In conclusion, the first article inspection of PCBA board is very important and must be paid attention to. As PCBA manufacturers, the first article inspection is of great significance. As electronic companies, the first article inspection can help better understand the situation of the cooperating manufacturers, which is very helpful for future cooperation and development.